Compact FTR Mini-Manual. Size, x8 inches. Twelve high-quality laminated pages, loaded with detailed instructions covering all aspects of operating. FTR/E Technical Supplement Dual Band FM Transceiver FTR/E Technical Supplement Introduction This manual provides technical. Yaesu FTR Amateur Transceiver. #, Nifty Mini Manual, MINI MANUAL, Nifty spiral bound mini-manual contains 12 laminated pages [ x 8 inch].
|Published (Last):||14 April 2006|
|PDF File Size:||2.59 Mb|
|ePub File Size:||17.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
If you have trouble getting your FTR to respond correctly during packet operation, check to be certain that you do not have Menu 26 PKT. Tone Search Scanning When this happens, it may be that the other station is not sending any tone.
Yaesu FT-7900R Mini-Manual
Shifting of CPU clock frequency. Just tap the button. Smart Search see above. The pin connections of the Data connector are shown below.
The number flashing will be the next available empty memory slot. Page of 84 Go. The computer program and cable available for these rigs is very nice, but if you pay attention and work carefully, you should be able to program this radio with 60 memories mwnual less than 1 hour.
Rear Panel Connections 10 Amperes continuous duty. Packet Interface Cable Availability of accessories may vary. You will then have to do step 10 again and continue from there. Depends on the band of operation.
Clockwise rotation of the DIAL knob maanual the FTR to be tuned toward a higher frequency, while counter-clockwise rotation will lower the operating frequency. It may be used for configuration of a wide variety of transceiver parameters, some of which have not been detailed previously. However, if you need to change the channel step increments, the procedure to do so is very easy; The brightness of the display is manually adjustable, using the following procedure: Almost every question you can ask about the FTR will be answered in the user manual.
Select the scan mode. To disable the Internet link feature, press the [ L ] key again. By pressing ‘print’ button you will print only current page. Adjust main dial to get receive frequency 3.
Push BAND momentarily to enable adjustment of tone 7.
Table of Contents Add to my manuals Add. When the Memory Bank manuxl is activated, the FTR will check the lowest memory channel in the Memory Bank as the priority channel. You can add HTML directly into this element to render on the page. Just edit this element to add your own HTML. Page 61 to establish the link to the Internet link repeater.
Cw Identifier Setup Don’t have an account?
Specifications AF Output Impedance: Press and hold in the [ S. Priority Channel” Scanning dual Watch 4. Operation is subject to the following two conditions; 1 This device may not cause harmful interference, and 2 this device must accept any interference including received, interference that may cause undesired operation.
Notting HillVictoria, Australia.
Programming The FT-7900R
Menu 6 [ CLK. When this happens, it may be that the other station is not sending any tone.
Read the manual completely. Page 19 Press or hold in either of these buttons to tune or scan up or down the operating frequency or through the memory channels. Auto” Mode Preset Operating Parameters As with all of the recent Yaesu radios, there is a big difference as to what you will get if you hold the button too long, or not long enough. Memory Only Mode 3. Press or hold in 79000r of these buttons to tune or scan up or down the operating frequency or through the memory channels.
Page 70 Selects or disables the VFO band edge limiting for the current band.
YAESU FTR OPERATING MANUAL Pdf Download.
While the MHz shift will be kHz; on 70 cm, the shift may be 1. Rotate main dial to select tone frequency.
Avoid heating vents and window kanual that could expose the transceiver to excessive direct sunlight, especially in hot climates. You can also program in the power level you wish to use on each memory by setting the power level while in VFO mode.
Page 59 4. Page 30 FM carrier in order to activate the repeater. Got it, continue to print.