ARITECH CS350 MANUAL PDF

CS Installation Instructions This manual contains installation details for the CS control panels. It provides the basic programming and. CS Installation InstructionsThis manual contains installation details for the CS control panels. It provides the basic programming and inst. You can examine Aritech CS Manuals and User Guides in PDF. View online or download 1 Manuals for Aritech CS Besides, it’s possible to examine.

Author: Mikasa Arajora
Country: Belize
Language: English (Spanish)
Genre: Business
Published (Last): 22 April 2010
Pages: 77
PDF File Size: 12.94 Mb
ePub File Size: 6.25 Mb
ISBN: 718-8-73540-533-7
Downloads: 31473
Price: Free* [*Free Regsitration Required]
Uploader: Fer

If the system does not activate, disarm and enter Engineer Mode. Confirm changes to the description shown on the display after programming. Silent or audible Personal Attack alarm is determined in function 6. Exit The exit time stops and system arms 4 seconds after Terminator closing the input.

Enter at Keypad 1 the default engineer’s code [0][1][2][7][8]. Check that the battery is connected correctly. It provides the basic programming and installation information required by technicians and engineers.

Disconnect bell manuwl from control panel and connect across battery observing correct polarity. Apply mains power to the panel. Tamper Input is 24Hrs operational. Triggering the input will activate the interior bell for 4 seconds,as well as latch and walk test outputs.

Check that the internal sounder is connected. Factory default code for user code01is []. The exact operation will be determined by the attributes allocated in function 4. The Display will prompt for the Language Default prefered.

Digital communicator fault input See also Peridiax aritecj on page Check if bell delay time is programmed for [00] ‘Timers Menu’ at ‘Bell Times’. The RKP will display the cause of trouble. Forced arming can be achieved in three ways.

  EDGECAM KRZYSZTOF AUGUSTYN PDF

Aritech CS350 Manuals

If set to Cs35 then this output resets when the system is disarmed. Now enter [] again to initialize the other keypad s. Ensure that the battery is fully charged ariteech is large enough to carry the load of the system. This means that both internal and c350 bells sound for a programmable number of minutes perimeter bell time. Replace the cover of the RKP and ensure that the tamper switch in the panel is closed. When only the zone attributes Ls is addedthen the panel will cause a local alarm for inertia sensor activations and a full alarm when the window opens.

Resets with disarm or start of entry time. Clear after exit Open zones are omitted till the exit time has expired, after which they can detect again. The following diagram shows how 4 RKPs may be connected using both methods. Additional keypads must be initialised by the panel before they become active.

Aritech CS Manuals

If after the exit time the zone is still open, the panel will not arm and act as programmed in function 6. Omnivista Installation Manual mail Download and install firefox Download. Aritech Corp assumes no responsibility for any errors which may appear in Documents. See also Peridiax programming on p.

Xs350 to programme is detailed on page 7. Chime, internal bell on Unused Input is not operational. Keypad Lock opening this input will disable access to the keypad. Wiring to Digital CommunicatorFigure Only applicable for Alarm types. mnual

  ELIPHAS LEVI EL GRAN ARCANO DEL OCULTISMO REVELADO PDF

The load of the bells is greater than the fuse rating, inserting a higher value manuzl may damage the panel. Published on Mar View Keyswitch arms panel without exit time. Use ‘Show Open Zones’ menu to do this.

System does not activate when Tamper opens during day ie when system is disarmed. See the Programming Map and Programming Functions for operational details. Clear when closed Open zones are omitted till they close again. Activation of input causes ‘internal bell’ alarm in disarmed state and full alarm in armed state.

When programmed for ‘-‘ trigger the output will switch to ‘-‘ with an alarm condition. Any combination of the above wiring methods is allowed with the restriction that the total cable length on each of the wiring loops either multidrop or star is restricted to m. Remove the plug-on link JP1 on the panel. Alarm Input is only active when the system is armed and it will act according to its programmed attributes.

Aritech CS350 Manuals & User Guides

ce350 Setting to ‘0’ disables the code. Features and options are grouped together and allocated to 6 main menu blocks: Confirm [] these changes when they are correct. System Clear Reflects the system status according to the optionsprogrammed in function 6.