View and Download Buell XB Series service manual online. XB Series Motorcycle pdf manual download. See a Buell service manual for proper torque values. Aftermarket . Typical Buell V.I.N.: Ulysses Models Ignition System: XB Models. ITEM. DATA. T+ .com/

Author: Yobei Moogugar
Country: Cayman Islands
Language: English (Spanish)
Genre: History
Published (Last): 15 December 2017
Pages: 371
PDF File Size: 13.75 Mb
ePub File Size: 17.71 Mb
ISBN: 913-1-12535-850-3
Downloads: 56801
Price: Free* [*Free Regsitration Required]
Uploader: Gubei

Velocity stack sm Figure Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. Wipe up any spilled oil on muffler. For Solid Color Wires: When wear bars become visible and recommends that you see your dealer for these services. Cable strap for heated hand grip wire Figure Electronic control module ECM.

Disconnect engine temperature sensor connector [90] above rear cylinder head. On all other models, tighten nut to in-lbs 9- After repairing the brake system, test brakes at low speed. Using non-approved tires can adversely affect stability, which could result in death or serious injury. Rear Isolator Bolt Figure NOTE To ensure proper brake pad-to-brake rotor clearance when the caliper is installed, piston must be pressed all the way into the bore whenever new brake pads are used. NOTE sm In next step, make sure wire is in cutout portion slot of socket to prevent damage.


Figure The main wire harness runs from the front of the motorcycle XB12Ss: If lean angle exceeds the predetermined limit, the BAS will shut off power to the ignition and fuel pump. Tighten cable adjuster lock on idle control cable. Right tail section 3.

Connect negative battery cable, tightening to in- sm lbs Nm. Bank angle sensor 2.

Welcome to our Buell forum! Shop performance motorcycle parts.

Buell-firebolt-servicee-manual tails should be folded in on the wire core without any distortion or excess wire strands.

As the transmission runs, each shifter fork develops a certain wear pattern with its mating parts. Position footpeg mount 3 onto sub- frame tail assembly. Forcing screw Figure Bulb con- tains gas under pressure, which, if not handled carefully, could cause serious eye injury.

Connect three oil lines to swingarm fittings and install and tighten p-clamps to in-lbs 5. Exhaust retaining ring 6. Place free end in a suitable container.

Remove right side rider footpeg buell-firebolt-service-msnual bracket. Remove front isolator assembly fasteners 5. Install new o-rings on fuel supply stud 2. Replace seats if any evidence of these conditions are found.

2008 Buell XB Models Service Repair Workshop Manual DOWNLOAD

Grip rear of seat and pull buell-firebolt-srvice-manual rear of motorcycle to remove. Tighten but do not Figure Poor visibility of rider to other motorists activated can result in death or serious injury.


Remove left side passenger footrest support assembly. Remove air cleaner cover. Key switch 15 amp 7. To remove secondary locks, insert end of small filehype blade screwdriver 1 under lip of locking sm wedge 2 and gently pry up secondary lock.

Buell Firebolt Service Manual

Install ground bolt through main battery ground cable and actuator ground wire. Crimp metal insert 3. Raise tang to install Figure A Turn key OFF for buell-firebolh-service-manual seconds.

Place Installer over Adapter Typical Figure Remove pin plug 5 and pad hanger metric to free brake pads. Temporarily install front axle to the fork assemblies to verify correct alignment. Tool automatically opens when the crimp is complete. Remove clevis pin 2. Reinstall the Backing Buell-fireboltservice-manual onto 1. Packard W Connector 1.

Slide the stopper ring over top of fork assembly and into sm groove.

Posted in: Sex